Pogoste težave s plesnijo

1. Raw edges
2. a) Confirm whether the number of frames and vpenjalna silaanaliza vzrokov zloma veznega droga stroja za brizganje brizgalni stroj are sufficient
3. b) Preverite, ali je tlak previsok

1) Če ima nenasičen vzorec še vedno robove, to pomeni, da vpenjanje kalupa ni dobro ali da je napaka pokvarjena.

2) If the mold clamping is not good and the size is too small when the pressure is reduced, the size problem needs to be confirmed

1. c) Poor clamping → re-closing

2. Breaking

Poor discharge positioning of male and female molds or wrong electrode size → put them in place again (need to evaluate the difficulty of mold repair, whether

(Under the influence of function and appearance, the size can be allowed to be larger)

3. Pull the male mold (deformacija)

1. a) Insufficient lighting (scratches, whitening or deformation) → Strengthen lighting
2. b) Insufficient draft angle → The draft angle can be increased without affecting the function or shrinking the appearance.
3. c) Insufficient ejection, unevenness → add ejector pin or change ejection position
4. Da bi preprečili slab povratni tok ali neenakomerno hlajenje) Slabo pozicioniranje zdrsa ejektorja → Izmetna glava ugrizne, da poveča trenje
5. e) Tlak vbrizga je prevelik (predvsem v bližini dovoda, vstopni položaj je slabo izbran ali pa je meso pretanko, da bi oviralo pretok)

→Spremenite položaj hranjenja ali povečajte debelino mesa, da olajšate pretok (če se videz ne skrči in ne vpliva na funkcijo)

4. Potegnite mojstra je dolgo časa pod stresom
5. a) Podrez plesni:

(1) Napaka pri načrtovanju → spremenite dizajn

(2) Konstrukcijska napaka→spremeni kalup

1. b) Slabo grizenje:

(1) Ugrizni cvetno bodico → zasveti, močan ugriz ali delni ugriz

(2) Pregriz → osvetlitev

(3) Ugrizni pregloboko in nariši rožo (debelina ugriza, globina mora ustrezati kotu ugreza) → polirati, močan ugriz ali delni ugriz, po potrebi spremenite kot ugreza

1. c) Po grizenju cveta, poteg moške plesni je nezadosten → moška plesen ugrizne cvet ali potisne zatič, da ugrizne cvet in ga potegne nazaj
2. Prebijajoča senca

1. a) Hitrost ognja na vstopu je prehitra → zmanjšajte hitrost ognja ali povečajte vstop, vendar ne naredite prevelike velikosti za streljanje

majhna.

1. b) Hladna vrtina za polže ni dobra → Za primer vzemite kalup s štirimi luknjami, vodnjak za hladne polže x3 in glava za hladne polže x2 morata biti dovolj veliki

6. Fuzijska linija je očitna (slika se lahko prepiše)

1. a) The temperatura kalupaje prenizka → prilagodite temperaturo kalupa (vendar mora biti v okviru ustrezne masovne proizvodnje)
2. b) Nezadostno motenje → moški model grize grobe cvetove nad MT11030, in tok je moten
3. c) Nezadosten izhod zraka → Okrepite izhodni zrak (dodajte bloke za izhod zraka ali vbrizgajte, itd., če je potrebno, uhajanje zraka)
4. Položaj talilne linije povzroči, da se deli zlahka zlomijo

Če fuzijske linije ni mogoče odpraviti

1. a) Prilagodite gumb za nastavitev, da nadzirate neenakomerno količino dovajanja, da premaknete talilno linijo
2. b) Dovod dovoda je premaknjen

8. Zlomljena senca

Prevelika nihanja v višini javnega modela (nezadostna diferenciacija) vzrok za povečanje območja diferenciacije (bodite pozorni na težave z motnjami) Javni model je ugriznil hrapavo rožo in motil tok

9. Sijaj je drugačen

1. a) Preverite, ali je votlina kalupa mastna → očistite
2. b) Preverite, ali na votlino kalupa vpliva oprijem gumijastega kalupa, ki ga povzroča visoka temperatura kalupa → čiščenje
3. c) The mold temperature is wrong, the higher the temperature, the more foggy → adjust the mold temperature, adjust the temperature while shooting, and hit the color difference
4. Da bi preprečili slab povratni tok ali neenakomerno hlajenje) Encapsulation due to poor air escape → Strengthen the escape of air near the enclosure or the flow channel

A If at the biting position:

1. a) The thickness of the bite is the same as the depth. àCompared to the old parts and samples. b) Sandblasting error→Re-spraying
2. Lighting part:
3. a) The number of polished numbers is incorrect.
4. The color difference is different
5. a) Confirm resin
6. b) Adjust the mold temperature
7. Air bubbles (transparent material)
8. a) Poor escape gas → Strengthen escape gas (flow channel, escape gas block or burrs when necessary)
9. b) The rate of fire is too fast → adjust the machine
10. c) The injection pressure is too small → adjust the machine
11. Da bi preprečili slab povratni tok ali neenakomerno hlajenje) The inlet or runner is too small
12. e) Insufficient drying of rubber particles
13. The clamping line is obvious

1. a) Poor clamping → re-closing
2. b) Male and female mode breakage → (refer to breakage handling)

13. Poor filling:

1. a) Confirm the temperatura kalupa and whether the material temperature is too low and affect the fluidity b) Whether the shooting speed and the shooting pressure are too low
2. c) Is the inlet flow channel appropriate (large enough, wide enough, and deep enough?) Da bi preprečili slab povratni tok ali neenakomerno hlajenje) Is the exhaust gas sufficient?
3. e) Whether materials can be stolen (non-structural parts should be stolen as much as possible)
4. Shrink
5. a) Confirm whether the holding pressure is sufficient (if the mold burrs have occurred, the gauge pressure has been too large) b) Confirm whether the thickness of the shrinkage is too thick àStealing meat or adding materials nearby

15.Warpage

1. a) Whether the injection pressure is too large b) Whether the full pressure is too long c) The temperature difference between the male and female molds is wrong d) Whether the ejection is bad

16.Thimble Shadow

1. a) Confirm the time when the thimble shadow appears, before or after ejection?

Before ejection: The top plate of the mold is insufficiently rigid and deformed due to pressure After ejection: The meat is too thin or the ejection is too deep or too shallow

Če želite vedeti, kateri analiza vzrokov zloma veznega droga stroja za brizganje vaš izdelek je primeren za, in poznate ceno stroja za brizganje, lahko kliknete spletno storitev za stranke ali pokličete za posvet! servisna telefonska linija: 8618958305290