Akrýl innspýtingsmótunarferli

Acrylic is chemically called polymethyl methacrylate (PMMA á ensku). Vegna galla PMMA yfirborðs hörku, auðvelt að klóra, lágt höggþol, léleg mótun vökva, o.s.frv., breytingin á PMMA hefur birst hvað eftir annað. Svo sem samfjölliðun metýlmetakrýlats með stýreni og bútadíen, blöndun PMMA og PC, osfrv.

The flow of PMMA is worse than that of PS and ABS, and the melt viscosity is more sensitive to temperature changes. During the mótunarferli, the melt viscosity is mainly changed from the injection temperature. PMMA is an amorphous polymer with a melting temperature greater than 160°C and a decomposition temperature of 270°C.

1. Plastic processing

PMMA has a certain degree of water absorption, with a water absorption rate of 0.3-0.4%, and the humidity of injection molding must be below 0.1%, venjulega 0.04%. The presence of water causes bubbles, gas lines, and reduced transparency in the melt. So it needs to be dried. The drying temperature is 80-90℃, and the time is more than 3 klukkustundir. Recycled materials can be used 100% í sumum tilfellum. The actual amount depends on quality requirements, usually over 30%. Recycled materials should avoid pollution, otherwise it will affect the transparency and the properties of the finished product.

Til

2. Sprautumótunarvél selection

PMMA has no special requirements for injection molding machines. Because of its high melt viscosity, a deeper screw groove and a larger diameter nozzle hole are required. If the strength of the product is higher, a screw with a larger length to diameter ratio should be used for low-temperature plasticization. Auk þess, PMMA must be stored in a dry hopper.

3. Mót og hlið hönnun

The mold hitastig can be 60℃-80℃, the diameter of the main runner should match the inner taper, the best angle is 5° to 7°, if you want to inject 4mm or more products, the angle should be 7°, and the diameter of the runner should reach 8 to 10mm, the overall length of the gate should not exceed 50mm. For products with a wall thickness of less than 4mm, the diameter of the runner should be 6-8mm

For products with wall thickness greater than 4mm, the runner diameter should be 8-12mm. Diagonal, fan-shaped and tabular gate depth should be 0.7 to 0.9t (t is the thickness of the product wall), and the diameter of the needle gate should be 0.8 to 2mm; smaller size should be used for low viscosity.

Til

The common vent holes have a depth of less than 0.05 and a width of 6mm. The demolding angle is between 30′-1° and 35′-1°30° in the cavity part.

Til

4. Melting temperature

It can be measured by air injection method: ranging from 210°C to 270°C, depending on the information provided by the supplier.

Withdraw the back seat, make the nozzle of the injection molding machine leave the sprue bushing, and then manually perform plasticization injection molding, which is air injection molding.

5. Inndælingarhitastig

Fast injection can be used, but to avoid high internal stress, it is advisable to use multi-stage injection, such as slow-fast-slow, o.s.frv., when injecting thick parts, use slow speed.

Til

6. Detention time

If the temperature is 260°C, the residence time cannot exceed 10 mínútur, and if the temperature is 270°C, the residence time cannot exceed 8 mínútur.

Ef þú hefur einhverjar spurningar um plastiðnaður,plz ekki hika við að spyrja FLYSE teymið,við munum veita þér bestu þjónustu!

Whatsapp / Wechat 008618958305290