Genep titik utama pp suntik molding

Genep titik utama pp suntik molding.The processing bahan baku palastik utamana ngalembereh, ngalir, wangun, lajeng tiis kana produk rengse. Ieu prosés pemanasan lajeng cooling. Éta ogé prosés dimana palastik robah tina pellets kana bentuk anu béda. The following will explain the processing from the perspectives of different stages. Prosés.

1. Melting

The heater allows the raw material particles to gradually melt into a fluid flow, which is mainly suitable for temperature adjustment of different raw materials. Increasing the temperature will tend to speed up the flow of raw materials, which can increase efficiency but may not guarantee yield. It must be suitable Balance.

Salaku tambahan, the good effect and the characteristics of high thermal cracking of PP are that it is best to make the raw materials flow smoothly to the die during production to avoid insufficient filling or backflow. Backflow means that the flow of raw materials is faster than the output rate. An increase in average flow efficiency equals an increase in MFR, nu mangrupa salah sahiji métode processing sadia, tapi ogé ngabalukarkeun distribusi MFR abnormal, nu bisa ngakibatkeun ngaronjat instability, nu bisa ningkatkeun laju cacad.

Nanging, éta produk PP sanes produk kalayan precision diménsi luhur kusabab aplikasi, jadi dampakna teu badag.

2. sekrup

Kalolobaan ngolah PP disetir ku screw pikeun ngajalankeun fluidity nu, jadi desain screw ngabogaan pangaruh hébat. Ukuran diaméterna mangaruhan kaluaran, jeung rasio komprési mangaruhan nilai tekanan jeung kaluaran jeung pangaruh produk rengse. Ieu ogé ngawengku rupa-rupa bahan. (Warna masterbatches, aditif jeung modifiers) pangaruh campur.

Aliran bahan baku utamana gumantung kana manaskeun, but the frictional heat of the raw materials will also generate frictional heat to accelerate the fluidity, so the screw compression ratio is small and the flow is small, and the rotation speed must be increased. The frictional heat will be more than that of the screw with a large compression ratio.

Ku sabab kitu, it is often said that there is no master in plastic processing, and the person who carefully understands the performance of the machine is the master. The heating of raw materials is not only a heater, but also the frictional heat and residence time.

So this is a practical problem, and experience helps solve production problems and efficiency. If the screw needs to have a particularly good mixing effect, sometimes two-stage different screws or twin-shaft screws are designed and different types of screws are divided into sections to achieve various mixing effects.

3. Mould or die head

Plastic reshaping relies on the mold or die head. The injection molded product is three-dimensional, and the mold is more complex, and shrinkage must be considered. The others are flat, strip, and needle-shaped continuous product die heads. If it is a special shape, It is classified as a special shape, and needs to pay attention to the problem of cooling and shaping immediately.

…

Most of the plastic machines are designed like injection syringes, and the extrusion force driven by the screw will cause huge pressure on the small outlets and improve production efficiency. When the die head is designed as a flat surface, how to make the raw materials evenly distributed on the entire surface is very important.

4.Cooling

In addition to the sprue gate pouring raw material, éta kapang suntik also has a cooling water channel to cool the raw material design. Extrusion molding relies on the cooling water channel in the roller to achieve the cooling effect, except for the air knife, the cooling water is directly poured on the blowing bag, and the cooling method such as hollow blowing.

5.Extension

The reprocessing and extension of the finished product will enhance the effect. Salaku conto, the strapping belt is driven by the front and rear rollers at different speeds to cause the extension effect. The tensile strength of the oriented extension part of the finished product is strengthened and it is not easy to tear, but it is very easy to tear in the horizontal direction. The molecular weight distribution also affects the extension effect during high-speed production. All extruded products including fibers have different extensions. Vacuum and pressure forming can also be regarded as another form of extension.

6, shrink

Any raw material has the problem of shrinkage. The shrinkage is caused by thermal expansion and cold shrinkage and internal stress generated during crystal formation.

…

Sacara umum, thermal expansion and contraction are easier to overcome, and the cooling time can be prolonged in processing, and the pressure can be maintained continuously. Crystalline raw materials tend to have larger shrinkage differences than non-crystalline materials, which is about one thousandth for PP. Sixteen, but ABS is only about four thousandths. Ieu bagian tina bédana kacida gedéna. Bagian ieu kedah diatasi dina kapang, atawa aditif réduksi shrinkage mindeng ditambahkeun pikeun nungkulan piring Tonjolan. LDPE mindeng ditambahkeun pikeun ngaronjatkeun masalah necking.